Get Ready to Embrace the Heat

Pulse Setup
Tutorial

Step 1

FRAME SETUP

(01) Each piece of the frame is labeled accordingly. Please lay all pieces out on the floor.

(02) We recommend starting with the bottom base first. Once the bottom of the frame is securely constructed, start by fully unzipping the frame cover.

(03) Place the bottom of the frame inside the bottom of the frame cover.

Frame poles: Bottom and Top halves
Frame parts: Floor, Middle, Roof layers and connectors
Assembled frame diagram showing all parts A–G

← Swipe to see all diagrams →

Step 2

Assemble Cover Over Frame

(06) Unzip the cover entirely and lay on the floor. Start by placing the base of the frame into the bottom of the cover so that all corners fit snug. The floor will be exposed as the velcro floor lining will be added after.

(07) After the frame's base is in the cover, pull the cover over the top of the frame. Secure the cover around the top corners and zip it around the frame. Finally, stand inside the frame and attach the velcro floor to match the velcro lining along the base.

Step 3

Insert Heating Panels

(08) Ensure all cables are disconnected from each other and are not plugged into a wall outlet. Remove all plastic wrapping on the panels.

(09) Unzip the sauna cover and insert (6) panels into mesh pockets of the sauna walls: Open the mesh pocket, insert the heating panel with the black side facing outward and the cable output on the bottom, protruding from the mesh pouch. Close the mesh panel.

(10) Repeat the above step for all 6 heating panels.

(11) When completed: All 6 panels should be secured in the mesh pockets with the cable connectors sticking out of the bottom of each pocket. Note: The panels are identical and interchangeable; they do not need to be used in any particular order.

PAIRING YOUR

REMOTE

(1) Pairing Your Remote: Your Pulse remote & controller system will not come paired via bluetooth. To pair your device, ensure that your controller is properly connected to power and to the cable bunch.

Then turn your remote on and wait for the "E1" error to pop up on the remote screen. After the "E1" error pops up, hit the On/Off button 6 times consecutively. You will know your device is paired when you hear a click from the controller box and the "El" error no longer shows up on your screen.

(2) Control Your Desired Settings: After the sauna is plugged into a standard home outlet, use the buttons on the remote to control your desired settings and allow the sauna to heat up for 15–20 minutes before entering.

(3) Using the Sauna Safely: Ensure you've read safety instructions. Start at lower temperatures to ensure you do not overheat. Do not leave the sauna on for more than 1 hour and unplug when not in use.

Pulse remote diagram

TROUBLESHOOTING

Select your error code below for step-by-step troubleshooting instructions.

The white remote is not paired to the control box.

Fix

  1. Turn on the Bluetooth Remote and wait for the E1 error code to pop up.
  2. Press the On/Off button 6 times consecutively & quickly.

Fix

  1. Verify remote control is in range of the Pulse Sauna (within 10ft).
  2. Verify the Pulse Pro control box is plugged into the wall outlet and all electrical connections are properly connected.
  3. Verify that the circuit protector (~6" away from the outlet plug) is not tripped. The "light" button should be lit (see picture below).
Circuit protector plug — the light button should be lit

Circuit protector plug — the "light" button should be lit

  1. If all 3 are verified, then: Turn off the Remote → Unplug from wall outlet → Wait 5 seconds → Plug back in → Turn remote back on → Receive E1 Error → Re-pair Remote.

Fix

  1. Turn off the Sauna.
  2. Take a picture of the E0 error and send to SaunaBox support — the team will send a replacement Control Box.

Fix

Place the temperature sensor right in front of the infrared heating panel. This will allow the temperature sensor to read the correct ambient temperature.

The black remote is not paired to the control box.

Fix

  1. Turn on the Bluetooth Remote and wait for the E1 error code to pop up.
  2. Press and hold the Bluetooth button for 3 seconds.

Fix

  1. Verify remote control is in range of the Pulse Sauna (within 10ft).
  2. Verify the Pulse Pro control box is plugged into the wall outlet and all electrical connections are properly connected.
  3. Verify that the circuit protector (~6" away from the outlet plug) is not tripped. The "light" button should be lit (see picture below).
Circuit protector plug — the light button should be lit

Circuit protector plug — the "light" button should be lit

  1. If all 3 are verified, then: Turn off the Remote → Unplug from wall outlet → Wait 5 seconds → Plug back in → Turn remote back on → Receive E1 Error → Re-pair Remote.

Fix

  1. Turn off the Sauna.
  2. Take a picture of the E0 error and send to SaunaBox support — the team will send a replacement Control Box.

Fix

Place the temperature sensor right in front of the infrared heating panel. This will allow the temperature sensor to read the correct ambient temperature.

Download PDF

Download Product Manual PDF

Red Light Tutorial

Red Light Setup Tutorial

Want To Earn Cash?
Become An Ambassador!

Share your custom link to earn an unlimited 5% cash from each purchase made through your link.

Any Questions?

Need more help? Contact our top rated support team and we'll help you out.


Contact Support

How To

Clean Your SaunaBox

Maintenance Overview
Enlarged view
1